periph_conf.h

Go to the documentation of this file.

/*
 * SPDX-FileCopyrightText: 2019 Inria
 * SPDX-FileCopyrightText: 2019 Freie Universität Berlin
 * SPDX-FileCopyrightText: 2019 Kaspar Schleiser <kaspar@schleiser.de>
 * SPDX-License-Identifier: LGPL-2.1-only
 */
 
#pragma once
 
/* This board provides an LSE */
#ifndef CONFIG_BOARD_HAS_LSE
#define CONFIG_BOARD_HAS_LSE    1
#endif
 
/* This board provides an HSE */
#ifndef CONFIG_BOARD_HAS_HSE
#define CONFIG_BOARD_HAS_HSE    1
#endif
 
/* The HSE provides a 12MHz clock */
#ifndef CONFIG_CLOCK_HSE
#define CONFIG_CLOCK_HSE               MHZ(12)
#endif
 
#include "periph_cpu.h"
#include "clk_conf.h"
#include "cfg_usb_otg_fs.h"
 
#ifdef __cplusplus
extern "C" {
#endif
 
static const dma_conf_t dma_config[] = {
    { .stream = 11 },   /* DMA2 Stream 3 - SPI1_TX */
    { .stream = 10 },   /* DMA2 Stream 2 - SPI1_RX */
};
 
#define DMA_0_ISR           isr_dma2_stream3
#define DMA_1_ISR           isr_dma2_stream2
 
#define DMA_NUMOF           ARRAY_SIZE(dma_config)
static const timer_conf_t timer_config[] = {
    {
        .dev      = TIM5,
        .max      = 0xffffffff,
        .rcc_mask = RCC_APB1ENR_TIM5EN,
        .bus      = APB1,
        .irqn     = TIM5_IRQn
    }
};
 
#define TIMER_0_ISR         isr_tim5
 
#define TIMER_NUMOF         ARRAY_SIZE(timer_config)
static const uart_conf_t uart_config[] = {
    {
        .dev        = USART1,
        .rcc_mask   = RCC_APB2ENR_USART1EN,
        .rx_pin     = GPIO_PIN(PORT_B, 7),
        .tx_pin     = GPIO_PIN(PORT_B, 6),
        .rx_af      = GPIO_AF7,
        .tx_af      = GPIO_AF7,
        .bus        = APB2,
        .irqn       = USART1_IRQn,
#ifdef MODULE_PERIPH_DMA
        .dma        = DMA_STREAM_UNDEF,
        .dma_chan   = UINT8_MAX,
#endif
    },
};
 
#define UART_0_ISR          (isr_usart1)
 
#define UART_NUMOF          ARRAY_SIZE(uart_config)
static const spi_conf_t spi_config[] = {
    {
        .dev            = SPI1,
        .mosi_pin       = GPIO_PIN(PORT_A, 7),
        .miso_pin       = GPIO_PIN(PORT_A, 6),
        .sclk_pin       = GPIO_PIN(PORT_A, 5),
        .cs_pin         = GPIO_UNDEF,
        .mosi_af        = GPIO_AF5,
        .miso_af        = GPIO_AF5,
        .sclk_af        = GPIO_AF5,
        .cs_af          = GPIO_AF5,
        .rccmask        = RCC_APB2ENR_SPI1EN,
        .apbbus         = APB2,
#ifdef MODULE_PERIPH_DMA
        .tx_dma         = 0,
        .tx_dma_chan    = 3,
        .rx_dma         = 1,
        .rx_dma_chan    = 3,
#endif
    }
};
 
#define SPI_NUMOF           ARRAY_SIZE(spi_config)
static const i2c_conf_t i2c_config[] = {
    {
        .dev            = I2C2,
        .speed          = I2C_SPEED_NORMAL,
        .scl_pin        = GPIO_PIN(PORT_B, 10),
        .sda_pin        = GPIO_PIN(PORT_B, 11),
        .scl_af         = GPIO_AF4,
        .sda_af         = GPIO_AF4,
        .bus            = APB1,
        .rcc_mask       = RCC_APB1ENR_I2C2EN,
        .clk            = CLOCK_APB1,
        .irqn           = I2C2_ER_IRQn,
    },
};
 
#define I2C_0_ISR           isr_i2c2_er
 
#define I2C_NUMOF           ARRAY_SIZE(i2c_config)
#ifdef __cplusplus
}
#endif