Board specific definitions for the SLTB001A starter kit. More...

Detailed Description

Board specific definitions for the SLTB001A starter kit.

Author: Hauke Petersen hauke.nosp@m..pet.nosp@m.ersen.nosp@m.@fu-.nosp@m.berli.nosp@m.n.de; Bas Stottelaar basst.nosp@m.otte.nosp@m.laar@.nosp@m.gmai.nosp@m.l.com

Definition in file board.h.

#include "cpu.h"
#include "periph_conf.h"
#include "periph/adc.h"
#include "periph/gpio.h"
#include "periph/spi.h"

Include dependency graph for board.h:

This graph shows which files directly or indirectly include this file:

Xtimer configuration
The timer runs at 250 kHz to increase accuracy, or at 32.768 kHz if LETIMER is used.
#define	XTIMER_DEV (TIMER_DEV(0))

#define	XTIMER_HZ (250000UL)

#define	XTIMER_WIDTH (16)

#define	XTIMER_CHAN (0)

Macros for controlling the on-board LEDs
#define	LED0_ON gpio_set(LED0_PIN)

#define	LED0_OFF gpio_clear(LED0_PIN)

#define	LED0_TOGGLE gpio_toggle(LED0_PIN)

#define	LED1_ON gpio_set(LED1_PIN)

#define	LED1_OFF gpio_clear(LED1_PIN)

#define	LED1_TOGGLE gpio_toggle(LED1_PIN)

Core temperature sensor configuration
Connection to the on-chip temperature sensor.
#define	CORETEMP_ADC ADC_LINE(0)

Environmental sensors configuration
Pin for enabling environmental sensors (BMP280, Si1133, Si7021, Si7210).
#define	ENV_SENSE_PIC_ADDR (0x01)

#define	ENV_SENSE_PIC_BIT (0)

Pressure sensor configuration
Connection to the on-board pressure sensor (BMP280).
#define	BMP280_I2C I2C_DEV(0)

#define	BMX280_PARAM_I2C_DEV BMP280_I2C

Air quality/gas sensor configuration
Connection to the on-board air quality/gas sensor (CCS811).
#define	CCS811_I2C I2C_DEV(0)

#define	CCS811_PIC_ADDR (0x03)

#define	CCS811_PIC_EN_BIT (0x00)

#define	CCS811_PIC_WAKE_BIT (0x01)

#define	CCS811_PARAM_I2C_DEV CCS811_I2C

IMU sensor configuration
Connection to the on-board IMU sensor (ICM-20648).
#define	ICM20648_ENABLED 0

#define	ICM20648_SPI SPI_DEV(0)

#define	ICM20648_PIC_ADDR (0x00)

#define	ICM20648_PIC_EN_BIT (0x00)

Power and Interrupt controller
Pin for communication with the Power and Interrupt Controller.
#define	PIC_INT_WAKE_PIN GPIO_PIN(PD, 10)

#define	PIC_I2C I2C_DEV(0)

#define	PIC_I2C_ADDR (0x48)

RGB leds configuration
There are four RGB leds on the board.
#define	RGB_LED1_ENABLED 1

#define	RGB_LED2_ENABLED 1

#define	RGB_LED3_ENABLED 1

#define	RGB_LED4_ENABLED 1

#define	RGB_LED_ADDR (0x04)

#define	RGB_LED_EN_BIT (0x00)

#define	RGB_LED1_EN_BIT (0x07)

#define	RGB_LED2_EN_BIT (0x06)

#define	RGB_LED3_EN_BIT (0x05)

#define	RGB_LED4_EN_BIT (0x04)

UV/Ambient sensor configuration
Connection to the on-board UV/ambient light sensor (Si1133).
#define	SI1133_ENABLED 0

#define	SI1133_I2C I2C_DEV(0)

Temperature sensor configuration
Connection to the on-board temperature/humidity sensor (Si7021).
#define	SI7021_I2C I2C_DEV(0)

#define	SI70XX_PARAM_I2C_DEV SI7021_I2C

Hall-effect sensor configuration
Connection to the on-board hall-effect sensor (Si7210). Available on Rev. A02 boards only.
#define	SI7210_ENABLED 0

#define	SI7210_I2C I2C_DEV(0)

Xtimer configuration