periph_conf.h

Go to the documentation of this file.

/*
 * SPDX-FileCopyrightText: 2016 Inria
 * SPDX-License-Identifier: LGPL-2.1-only
 */
 
#pragma once
 
/* This board provides an LSE */
#ifndef CONFIG_BOARD_HAS_LSE
#define CONFIG_BOARD_HAS_LSE    1
#endif
 
/* This board provides an HSE */
#ifndef CONFIG_BOARD_HAS_HSE
#define CONFIG_BOARD_HAS_HSE    1
#endif
 
#include "periph_cpu.h"
#include "clk_conf.h"
#include "cfg_i2c1_pb8_pb9.h"
#include "cfg_timer_tim5.h"
 
#ifdef __cplusplus
extern "C" {
#endif
 
static const dma_conf_t dma_config[] = {
    { .stream = 11 },   /* DMA2 Stream 3 - SPI1_TX */
    { .stream = 10 },   /* DMA2 Stream 2 - SPI1_RX */
};
 
#define DMA_0_ISR           isr_dma2_stream3
#define DMA_1_ISR           isr_dma2_stream2
 
#define DMA_NUMOF           ARRAY_SIZE(dma_config)
static const uart_conf_t uart_config[] = {
    {
        .dev        = USART2,
        .rcc_mask   = RCC_APB1ENR_USART2EN,
        .rx_pin     = GPIO_PIN(PORT_A, 3),
        .tx_pin     = GPIO_PIN(PORT_A, 2),
        .rx_af      = GPIO_AF7,
        .tx_af      = GPIO_AF7,
        .bus        = APB1,
        .irqn       = USART2_IRQn,
#ifdef MODULE_PERIPH_DMA
        .dma        = DMA_STREAM_UNDEF,
        .dma_chan   = UINT8_MAX,
#endif
    },
    {
        .dev        = USART1,
        .rcc_mask   = RCC_APB2ENR_USART1EN,
        .rx_pin     = GPIO_PIN(PORT_A, 10),
        .tx_pin     = GPIO_PIN(PORT_A, 9),
        .rx_af      = GPIO_AF7,
        .tx_af      = GPIO_AF7,
        .bus        = APB2,
        .irqn       = USART1_IRQn,
#ifdef MODULE_PERIPH_DMA
        .dma        = DMA_STREAM_UNDEF,
        .dma_chan   = UINT8_MAX,
#endif
    },
    {
        .dev        = USART6,
        .rcc_mask   = RCC_APB2ENR_USART6EN,
        .rx_pin     = GPIO_PIN(PORT_A, 12),
        .tx_pin     = GPIO_PIN(PORT_A, 11),
        .rx_af      = GPIO_AF8,
        .tx_af      = GPIO_AF8,
        .bus        = APB2,
        .irqn       = USART6_IRQn,
#ifdef MODULE_PERIPH_DMA
        .dma        = DMA_STREAM_UNDEF,
        .dma_chan   = UINT8_MAX,
#endif
    }
};
 
/* assign ISR vector names */
#define UART_0_ISR          (isr_usart2)
#define UART_1_ISR          (isr_usart1)
#define UART_2_ISR          (isr_usart6)
 
/* deduct number of defined UART interfaces */
#define UART_NUMOF          ARRAY_SIZE(uart_config)
static const spi_conf_t spi_config[] = {
    {
        .dev            = SPI1,
        .mosi_pin       = GPIO_PIN(PORT_A, 7),
        .miso_pin       = GPIO_PIN(PORT_A, 6),
        .sclk_pin       = GPIO_PIN(PORT_A, 5),
        .cs_pin         = GPIO_PIN(PORT_A, 4),
        .mosi_af        = GPIO_AF5,
        .miso_af        = GPIO_AF5,
        .sclk_af        = GPIO_AF5,
        .cs_af          = GPIO_AF5,
        .rccmask        = RCC_APB2ENR_SPI1EN,
        .apbbus         = APB2,
#ifdef MODULE_PERIPH_DMA
        .tx_dma         = 0,
        .tx_dma_chan    = 3,
        .rx_dma         = 1,
        .rx_dma_chan    = 3,
#endif
    }
};
 
#define SPI_NUMOF           ARRAY_SIZE(spi_config)
static const adc_conf_t adc_config[] = {
    {GPIO_PIN(PORT_A, 0), 0, 0},
    {GPIO_PIN(PORT_A, 1), 0, 1},
    {GPIO_PIN(PORT_A, 4), 0, 4},
    {GPIO_PIN(PORT_B, 0), 0, 8},
    {GPIO_PIN(PORT_C, 1), 0, 11},
    {GPIO_PIN(PORT_C, 0), 0, 10},
    {GPIO_UNDEF, 0, 18}, /* VBAT */
};
 
#define VBAT_ADC            ADC_LINE(6) 
#define ADC_NUMOF           ARRAY_SIZE(adc_config)
#ifdef __cplusplus
}
#endif