board.h

Go to the documentation of this file.

/*
 * Copyright (C) 2023 Gunar Schorcht <gunar@schorcht.net>
 *
 * This file is subject to the terms and conditions of the GNU Lesser
 * General Public License v2.1. See the file LICENSE in the top level
 * directory for more details.
 */
 
#pragma once
 
#include "board_common.h"
#include "periph/gpio.h"
 
#ifdef __cplusplus
extern "C" {
#endif
 
#define BTN0_PIN            GPIO_PIN(PORT_A, 8)
#define BTN0_MODE           GPIO_IN
#define BTN0_INT_FLANK      GPIO_RISING
#define LED0_PIN            GPIO_PIN(PORT_C, 13)
#define LED0_MASK           (1 << 13)
#define LED0_ON             (GPIOC->BC = LED0_MASK)
#define LED0_OFF            (GPIOC->BOP = LED0_MASK)
#define LED0_TOGGLE         (GPIOC->OCTL ^= LED0_MASK)
 
#define LED1_PIN            GPIO_PIN(PORT_A, 1)
#define LED1_MASK           (1 << 1)
#define LED1_ON             (GPIOA->BC = LED1_MASK)
#define LED1_OFF            (GPIOA->BOP = LED1_MASK)
#define LED1_TOGGLE         (GPIOA->OCTL ^= LED1_MASK)
 
#define LED2_PIN            GPIO_PIN(PORT_A, 2)
#define LED2_MASK           (1 << 2)
#define LED2_ON             (GPIOA->BC = LED2_MASK)
#define LED2_OFF            (GPIOA->BOP = LED2_MASK)
#define LED2_TOGGLE         (GPIOA->OCTL ^= LED2_MASK)
 
#define LED_RED_PIN         LED0_PIN    
#define LED_GREEN_PIN       LED1_PIN    
#define LED_BLUE_PIN        LED2_PIN    
#define MTD_0 mtd_dev_get(0)          
#define SDCARD_SPI_PARAM_SPI         SPI_DEV(0)
#define SDCARD_SPI_PARAM_CS          GPIO_PIN(PORT_B, 12)
#define SDCARD_SPI_PARAM_CLK         GPIO_PIN(PORT_B, 13)
#define SDCARD_SPI_PARAM_MISO        GPIO_PIN(PORT_B, 14)
#define SDCARD_SPI_PARAM_MOSI        GPIO_PIN(PORT_B, 15)
#if defined(MODULE_ST77XX) && defined(BOARD_SIPEED_LONGAN_NANO_TFT)
#define ST77XX_PARAM_SPI          SPI_DEV(1)            
#define ST77XX_PARAM_SPI_CLK      SPI_CLK_5MHZ          
#define ST77XX_PARAM_SPI_MODE     SPI_MODE_0            
#define ST77XX_PARAM_CS           GPIO_PIN(PORT_B, 2)   
#define ST77XX_PARAM_DCX          GPIO_PIN(PORT_B, 0)   
#define ST77XX_PARAM_RST          GPIO_PIN(PORT_B, 1)   
#define ST77XX_PARAM_RGB          0                     
#define ST77XX_PARAM_INVERTED     1                     
#define ST77XX_PARAM_NUM_LINES    160U                  
#define ST77XX_PARAM_RGB_CHANNELS 80U                   
#define ST77XX_PARAM_ROTATION     ST77XX_ROTATION_270   
#define ST77XX_PARAM_OFFSET_Y     25                    
#endif
 
#ifdef __cplusplus
}
#endif