board.h

Go to the documentation of this file.

/*
 * SPDX-FileCopyrightText: 2024 Marian Buschsieweke
 * SPDX-License-Identifier: LGPL-2.1-only
 */
 
#pragma once
 
#include "cpu.h"
#include "periph/gpio.h"
#include "cc2538_eui_primary.h"
 
#ifdef __cplusplus
extern "C" {
#endif
 
#define LED_GREEN_PIN       GPIO_PIN(PORT_C, 0) 
#define LED_GREEN_PORT      GPIO_C              
#define LED_GREEN_BIT       (1U << 0)           
#define LED0_PIN            LED_GREEN_PIN       
#define LED0_PORT           LED_GREEN_PORT      
#define LED0_BIT            LED_GREEN_BIT       
#define LED_RED_PIN         GPIO_PIN(PORT_C, 1) 
#define LED_RED_PORT        GPIO_C              
#define LED_RED_BIT         (1U << 1)           
#define LED1_PIN            LED_RED_PIN         
#define LED1_PORT           LED_RED_PORT        
#define LED1_BIT            LED_RED_BIT         
#define LED_YELLOW_PIN      GPIO_PIN(PORT_B, 1) 
#define LED_YELLOW_PORT     GPIO_B              
#define LED_YELLOW_BIT      (1U << 1)           
#define LED2_PIN            LED_YELLOW_PIN      
#define LED2_PORT           LED_YELLOW_PORT     
#define LED2_BIT            LED_YELLOW_BIT      
#define LED_BLUE_PIN        GPIO_PIN(PORT_B, 0) 
#define LED_BLUE_PORT       GPIO_B              
#define LED_BLUE_BIT        (1U << 0)           
#define LED3_PIN            LED_BLUE_PIN        
#define LED3_PORT           LED_BLUE_PORT       
#define LED3_BIT            LED_BLUE_BIT        
#define LED0_ON             (LED0_PORT->DATA |=  LED0_BIT)
#define LED0_OFF            (LED0_PORT->DATA &= ~LED0_BIT)
#define LED0_TOGGLE         (LED0_PORT->DATA ^=  LED0_BIT)
 
#define LED1_ON             (LED1_PORT->DATA |=  LED1_BIT)
#define LED1_OFF            (LED1_PORT->DATA &= ~LED1_BIT)
#define LED1_TOGGLE         (LED1_PORT->DATA ^=  LED1_BIT)
 
#define LED2_ON             (LED2_PORT->DATA |=  LED2_BIT)
#define LED2_OFF            (LED2_PORT->DATA &= ~LED2_BIT)
#define LED2_TOGGLE         (LED2_PORT->DATA ^=  LED2_BIT)
 
#define LED3_ON             (LED3_PORT->DATA |=  LED3_BIT)
#define LED3_OFF            (LED3_PORT->DATA &= ~LED3_BIT)
#define LED3_TOGGLE         (LED3_PORT->DATA ^=  LED3_BIT)
#define BTN_LEFT_PIN        GPIO_PIN(PORT_C, 4) 
#define BTN_LEFT_MODE       GPIO_IN_PU          
#define BTN0_PIN            BTN_LEFT_PIN        
#define BTN0_MODE           BTN_LEFT_MODE       
#define BTN_RIGHT_PIN       GPIO_PIN(PORT_C, 5) 
#define BTN_RIGHT_MODE      GPIO_IN_PU          
#define BTN1_PIN            BTN_RIGHT_PIN       
#define BTN1_MODE           BTN_RIGHT_MODE      
#define BTN_UP_PIN          GPIO_PIN(PORT_C, 6) 
#define BTN_UP_MODE         GPIO_IN_PU          
#define BTN2_PIN            BTN_UP_PIN          
#define BTN2_MODE           BTN_UP_MODE         
#define BTN_DOWN_PIN        GPIO_PIN(PORT_C, 7) 
#define BTN_DOWN_MODE       GPIO_IN_PU          
#define BTN3_PIN            BTN_DOWN_PIN        
#define BTN3_MODE           BTN_DOWN_MODE       
#define BTN_SELECT_PIN      GPIO_PIN(PORT_A, 3) 
#define BTN_SELECT_MODE     GPIO_IN_PU          
#define BTN4_PIN            BTN_SELECT_PIN      
#define BTN4_MODE           BTN_SELECT_MODE     
#ifndef UPDATE_CCA
#define UPDATE_CCA                1
#endif
 
#define CCA_BACKDOOR_ENABLE       1
#define CCA_BACKDOOR_PORT_A_PIN   3 
#define CCA_BACKDOOR_ACTIVE_LEVEL 0 
#ifdef __cplusplus
} /* end extern "C" */
#endif