board.h
Go to the documentation of this file.
1 /*
2  * SPDX-FileCopyrightText: 2017 Kees Bakker, SODAQ
3  * SPDX-License-Identifier: LGPL-2.1-only
4  */
5 
6 #pragma once
7 
18 #include "cpu.h"
19 #include "board_common.h"
20 #include "periph/gpio.h"
21 
22 #ifdef __cplusplus
23 extern "C" {
24 #endif
25 
30 #define LED0_PIN GPIO_PIN(PA, 15)
31 
32 #define LED0_PORT PORT->Group[PA]
33 #define LED0_MASK (1 << 15)
34 
35 #define LED0_OFF (LED0_PORT.OUTSET.reg = LED0_MASK)
36 #define LED0_ON (LED0_PORT.OUTCLR.reg = LED0_MASK)
37 #define LED0_TOGGLE (LED0_PORT.OUTTGL.reg = LED0_MASK)
38 
39 #define LED1_PIN GPIO_PIN(PB, 10)
40 
41 #define LED1_PORT PORT->Group[PB]
42 #define LED1_MASK (1 << 10)
43 
44 #define LED1_OFF (LED1_PORT.OUTSET.reg = LED1_MASK)
45 #define LED1_ON (LED1_PORT.OUTCLR.reg = LED1_MASK)
46 #define LED1_TOGGLE (LED1_PORT.OUTTGL.reg = LED1_MASK)
47 
48 #define LED2_PIN GPIO_PIN(PB, 11)
49 
50 #define LED2_PORT PORT->Group[PB]
51 #define LED2_MASK (1 << 11)
52 
53 #define LED2_OFF (LED2_PORT.OUTSET.reg = LED2_MASK)
54 #define LED2_ON (LED2_PORT.OUTCLR.reg = LED2_MASK)
55 #define LED2_TOGGLE (LED2_PORT.OUTTGL.reg = LED2_MASK)
62 #define BTN0_PIN GPIO_PIN(PA, 16)
63 #define BTN0_MODE GPIO_IN
70 #define GPS_TIMEPULSE_PIN GPIO_PIN(PA, 14)
71 #define GPS_TIMEPULSE_MODE GPIO_IN
78 #define GPS_ENABLE_PIN GPIO_PIN(PA, 18)
79 
80 #define GPS_ENABLE_PORT PORT->Group[PA]
81 #define GPS_ENABLE_MASK (1 << 18)
82 
83 #define GPS_ENABLE_ON (GPS_ENABLE_PORT.OUTSET.reg = GPS_ENABLE_MASK)
84 #define GPS_ENABLE_OFF (GPS_ENABLE_PORT.OUTCLR.reg = GPS_ENABLE_MASK)
91 #define LORA_RESET_PIN GPIO_PIN(PA, 4)
92 
93 #define LORA_RESET_PORT PORT->Group[PA]
94 #define LORA_RESET_MASK (1 << 4)
95 
96 #define LORA_RESET_OFF (LORA_RESET_PORT.OUTSET.reg = LORA_RESET_MASK)
97 #define LORA_RESET_ON (LORA_RESET_PORT.OUTCLR.reg = LORA_RESET_MASK)
98 #define LORA_RESET_TOGGLE (LORA_RESET_PORT.OUTTGL.reg = LORA_RESET_MASK)
101 #ifdef __cplusplus
102 }
103 #endif
104 
gpio.h
Low-level GPIO peripheral driver interface definitions.