periph_conf.h

Go to the documentation of this file.

/*
 * SPDX-FileCopyrightText: 2020 Inria
 * SPDX-License-Identifier: LGPL-2.1-only
 */
 
#pragma once
 
#include "periph_cpu.h"
 
#ifdef __cplusplus
extern "C" {
#endif
 
#define CLOCK_USE_PLL       (1)
 
#if CLOCK_USE_PLL
/* edit these values to adjust the PLL output frequency */
#define CLOCK_PLL_MUL       (47U)               /* must be >= 31 & <= 95 */
#define CLOCK_PLL_DIV       (1U)                /* adjust to your needs */
/* generate the actual used core clock frequency */
#define CLOCK_CORECLOCK     (((CLOCK_PLL_MUL + 1) * 1000000U) / CLOCK_PLL_DIV)
#else
/* edit this value to your needs */
#define CLOCK_DIV           (1U)
/* generate the actual core clock frequency */
#define CLOCK_CORECLOCK     (8000000 / CLOCK_DIV)
#endif
static const tc32_conf_t timer_config[] = {
    {   /* Timer 0 - System Clock */
        .dev            = TC3,
        .irq            = TC3_IRQn,
        .pm_mask        = PM_APBCMASK_TC3,
        .gclk_ctrl      = GCLK_CLKCTRL_ID_TCC2_TC3,
#if CLOCK_USE_PLL || CLOCK_USE_XOSC32_DFLL
        .gclk_src       = SAM0_GCLK_1MHZ,
#else
        .gclk_src       = SAM0_GCLK_MAIN,
#endif
        .flags          = TC_CTRLA_MODE_COUNT16,
    },
    {   /* Timer 1 */
        .dev            = TC4,
        .irq            = TC4_IRQn,
        .pm_mask        = PM_APBCMASK_TC4 | PM_APBCMASK_TC5,
        .gclk_ctrl      = GCLK_CLKCTRL_ID_TC4_TC5,
#if CLOCK_USE_PLL || CLOCK_USE_XOSC32_DFLL
        .gclk_src       = SAM0_GCLK_1MHZ,
#else
        .gclk_src       = SAM0_GCLK_MAIN,
#endif
        .flags          = TC_CTRLA_MODE_COUNT32,
    }
};
 
#define TIMER_0_MAX_VALUE   0xffff
 
/* interrupt function name mapping */
#define TIMER_0_ISR         isr_tc3
#define TIMER_1_ISR         isr_tc4
 
#define TIMER_NUMOF         ARRAY_SIZE(timer_config)
static const uart_conf_t uart_config[] = {
    {
        .dev      = &SERCOM5->USART,
        .rx_pin   = GPIO_PIN(PB,23),
        .tx_pin   = GPIO_PIN(PB,22),
#ifdef MODULE_SAM0_PERIPH_UART_HW_FC
        .rts_pin  = GPIO_UNDEF,
        .cts_pin  = GPIO_UNDEF,
#endif
        .mux      = GPIO_MUX_D,
        .rx_pad   = UART_PAD_RX_3,
        .tx_pad   = UART_PAD_TX_2,
        .flags    = UART_FLAG_NONE,
        .gclk_src = SAM0_GCLK_MAIN,
    }
};
 
/* interrupt function name mapping */
#define UART_0_ISR          isr_sercom5
 
#define UART_NUMOF          ARRAY_SIZE(uart_config)
#define PWM_0_EN            1
#define PWM_1_EN            1
 
#if PWM_0_EN
/* PWM0 channels */
static const pwm_conf_chan_t pwm_chan0_config[] = {
    /* GPIO pin, MUX value, TCC channel */
    { GPIO_PIN(PA, 4), GPIO_MUX_E, 0},
    { GPIO_PIN(PA, 5), GPIO_MUX_E, 1},
};
#endif
#if PWM_1_EN
/* PWM1 channels */
static const pwm_conf_chan_t pwm_chan1_config[] = {
    /* GPIO pin, MUX value, TCC channel */
    { GPIO_PIN(PA, 10), GPIO_MUX_E,  0 },
    { GPIO_PIN(PA, 11), GPIO_MUX_E,  1 },
};
#endif
 
/* PWM device configuration */
static const pwm_conf_t pwm_config[] = {
#if PWM_0_EN
    {TCC_CONFIG(TCC0), pwm_chan0_config, ARRAY_SIZE(pwm_chan0_config), SAM0_GCLK_MAIN},
#endif
 
#if PWM_1_EN
    {TCC_CONFIG(TCC1), pwm_chan1_config, ARRAY_SIZE(pwm_chan1_config), SAM0_GCLK_MAIN},
#endif
};
 
/* number of devices that are actually defined */
#define PWM_NUMOF           ARRAY_SIZE(pwm_config)
/* ADC Default values */
#define ADC_PRESCALER                       ADC_CTRLB_PRESCALER_DIV512
 
#define ADC_NEG_INPUT                       ADC_INPUTCTRL_MUXNEG_GND
#define ADC_GAIN_FACTOR_DEFAULT             ADC_INPUTCTRL_GAIN_1X
#define ADC_REF_DEFAULT                     ADC_REFCTRL_REFSEL_INT1V
 
static const adc_conf_chan_t adc_channels[] = {
    /* port, pin, muxpos */
    { .inputctrl = ADC_INPUTCTRL_MUXPOS_PA02 },    /* A0 */
    { .inputctrl = ADC_INPUTCTRL_MUXPOS_PB02 },   /* A1 */
    { .inputctrl = ADC_INPUTCTRL_MUXPOS_PA11 },  /* A2 */
    { .inputctrl = ADC_INPUTCTRL_MUXPOS_PA10 },  /* A3 */
    { .inputctrl = ADC_INPUTCTRL_MUXPOS_PB08 },    /* A4 */
    { .inputctrl = ADC_INPUTCTRL_MUXPOS_PB09 },    /* A5 */
    { .inputctrl = ADC_INPUTCTRL_MUXPOS_PA09 },   /* A6 */
    { .inputctrl = ADC_INPUTCTRL_MUXPOS_PB03 },   /* A7 */
};
 
#define ADC_NUMOF                           ARRAY_SIZE(adc_channels)
static const i2c_conf_t i2c_config[] = {
    {
        .dev      = &(SERCOM4->I2CM),
        .speed    = I2C_SPEED_NORMAL,
        .scl_pin  = GPIO_PIN(PB, 9),
        .sda_pin  = GPIO_PIN(PB, 8),
        .mux      = GPIO_MUX_D,
        .gclk_src = SAM0_GCLK_MAIN,
        .flags    = I2C_FLAG_NONE
     }
};
#define I2C_NUMOF           ARRAY_SIZE(i2c_config)
static const spi_conf_t spi_config[] = {
    {   /* Connected to NINA W102 */
        .dev      = &SERCOM2->SPI,
        .miso_pin = GPIO_PIN(PA, 13),
        .mosi_pin = GPIO_PIN(PA, 12),
        .clk_pin  = GPIO_PIN(PA, 15),
        .miso_mux = GPIO_MUX_C,
        .mosi_mux = GPIO_MUX_C,
        .clk_mux  = GPIO_MUX_C,
        .miso_pad = SPI_PAD_MISO_1,
        .mosi_pad = SPI_PAD_MOSI_0_SCK_3,
        .gclk_src = SAM0_GCLK_MAIN,
    },
    {
        .dev = &SERCOM3->SPI,
        .miso_pin = GPIO_PIN(PA, 19),
        .mosi_pin = GPIO_PIN(PA, 16),
        .clk_pin = GPIO_PIN(PA, 17),
        .miso_mux = GPIO_MUX_D,
        .mosi_mux = GPIO_MUX_D,
        .clk_mux = GPIO_MUX_D,
        .miso_pad = SPI_PAD_MISO_3,
        .mosi_pad = SPI_PAD_MOSI_0_SCK_1,
        .gclk_src = SAM0_GCLK_MAIN,
    },
};
 
#define SPI_NUMOF           ARRAY_SIZE(spi_config)
#ifndef RTT_FREQUENCY
#define RTT_FREQUENCY       (32768U)    /* in Hz. For changes see `rtt.c` */
#endif
static const sam0_common_usb_config_t sam_usbdev_config[] = {
    {
        .dm     = GPIO_PIN(PA, 24),
        .dp     = GPIO_PIN(PA, 25),
        .d_mux  = GPIO_MUX_G,
        .device = &USB->DEVICE,
        .gclk_src = SAM0_GCLK_MAIN,
    }
};
#ifdef __cplusplus
}
#endif