cpu.h

Go to the documentation of this file.

/*
 * Copyright (C) 2015 Kaspar Schleiser <kaspar@schleiser.de>
 *               2014 Freie Universität Berlin, Hinnerk van Bruinehsen
 *               2018 RWTH Aachen, Josua Arndt <jarndt@ias.rwth-aachen.de>
 *               2021-2023 Gerson Fernando Budke <nandojve@gmail.com>
 *
 * This file is subject to the terms and conditions of the GNU Lesser
 * General Public License v2.1. See the file LICENSE in the top level
 * directory for more details.
 */
 
#pragma once
 
#include <stdio.h>
#include <stdint.h>
 
#include <avr/interrupt.h>
#include "architecture.h"
#include "cpu_conf.h"
#include "cpu_clock.h"
#include "sched.h"
#include "thread.h"
#include "states_internal.h"
 
#ifdef __cplusplus
extern "C"
{
#endif
 
#ifndef AVR8_PM_DISABLE_BOD_ON_SLEEP
#define AVR8_PM_DISABLE_BOD_ON_SLEEP 0 
#endif
#define CPU_CYCLES_PER_LOOP (7)
 
#define PERIPH_I2C_NEED_READ_REG
#define PERIPH_I2C_NEED_WRITE_REG
#define PERIPH_I2C_NEED_READ_REGS
#define PERIPH_I2C_NEED_WRITE_REGS
static inline void avr8_enter_isr(void)
{
    /* This flag is only called from IRQ context, and nested IRQs are not
     * supported as of now. The flag will be unset before the IRQ context is
     * left, so no need to use memory barriers or atomics here
     */
    ++avr8_state_irq_count;
}
 
#define AVR8_STATE_FLAG_UART_TX(uart)    (0x01U << uart)
 
static inline void avr8_uart_tx_set_pending(unsigned uart)
{
    avr8_state_uart |= AVR8_STATE_FLAG_UART_TX(uart);
}
 
static inline void avr8_uart_tx_clear_pending(unsigned uart)
{
    avr8_state_uart &= ~AVR8_STATE_FLAG_UART_TX(uart);
}
 
static inline int avr8_is_uart_tx_pending(void)
{
    return avr8_state_uart;
}
 
void avr8_exit_isr(void);
 
void avr8_clk_init(void);
 
static inline uinttxtptr_t __attribute__((always_inline)) cpu_get_caller_pc(void)
{
        uinttxtptr_t addr;
    __asm__ volatile(
        "ldi %D[dest], 0"                   "\n\t"
#if __AVR_3_BYTE_PC__
        "pop %C[dest] "      "\n\t"
#else
        "ldi %C[dest], 0"                   "\n\t"
#endif
        "pop %B[dest]"                      "\n\t"
        "pop %A[dest]"                      "\n\t"
        "push %A[dest]"                     "\n\t"
        "push %B[dest]"                     "\n\t"
#if __AVR_3_BYTE_PC__
        "push %C[dest] "      "\n\t"
#endif
        : [dest]    "=r"(addr)
        : /* no inputs */
        : "memory"
    );
 
    /* addr now contains instruction to return to, subtract one to get
     * the instruction that called this function. Also multiply by two to get
     * the byte position, rather than the (16 bit) instruction position */
    addr = (addr - 1 ) * 2;
    return addr;
}
 
void avr8_stdio_init(void);
 
void avr8_reset_cause(void);
 
#ifdef __cplusplus
}
#endif