sdcard_spi_internal.h

Go to the documentation of this file.

/*
 * Copyright (C) 2016 Michel Rottleuthner <michel.rottleuthner@haw-hamburg.de>
 *
 * This file is subject to the terms and conditions of the GNU Lesser
 * General Public License v2.1. See the file LICENSE in the top level
 * directory for more details.
 */
 
#pragma once
 
#ifdef __cplusplus
extern "C" {
#endif
 
#include "periph/spi.h"
#include "periph/gpio.h"
#include "stdbool.h"
#include "sdcard_spi.h"
#include "timex.h"
#include "board.h"
 
/* number of clocks that should be applied to the card on init
   before taking further actions (see sd spec. 6.4.1.1 Power Up Time of Card) */
#define SD_POWERSEQUENCE_CLOCK_COUNT 74
 
#define SD_CARD_PREINIT_CLOCK_PERIOD_US 10 /* used to generate 100 kHz clock in init phase*/
#define SD_CARD_WAIT_AFTER_POWER_UP_US  1000
 
/* R1 response bits (see sd spec. 7.3.2.1 Format R1) */
#define SD_R1_RESPONSE_PARAM_ERROR       (1<<6)
#define SD_R1_RESPONSE_ADDR_ERROR        (1<<5)
#define SD_R1_RESPONSE_ERASE_SEQ_ERROR   (1<<4)
#define SD_R1_RESPONSE_CMD_CRC_ERROR     (1<<3)
#define SD_R1_RESPONSE_ILLEGAL_CMD_ERROR (1<<2)
#define SD_R1_RESPONSE_ERASE_RESET       (1<<1)
#define SD_R1_RESPONSE_IN_IDLE_STATE     (0x01)
#define SD_INVALID_R1_RESPONSE           (1<<7)
 
#define R1_VALID(X) (((X) >> 7) == 0)
#define R1_PARAM_ERR(X)   ((((X) &SD_R1_RESPONSE_PARAM_ERROR) != 0))
#define R1_ADDR_ERR(X)    ((((X) &SD_R1_RESPONSE_ADDR_ERROR) != 0))
#define R1_ERASE_ERR(X)   ((((X) &SD_R1_RESPONSE_ERASE_SEQ_ERROR) != 0))
#define R1_CMD_CRC_ERR(X) ((((X) &SD_R1_RESPONSE_CMD_CRC_ERROR) != 0))
#define R1_ILL_CMD_ERR(X) ((((X) &SD_R1_RESPONSE_ILLEGAL_CMD_ERROR) != 0))
#define R1_IDLE_BIT_SET(X) (((X) &SD_R1_RESPONSE_IN_IDLE_STATE) != 0)
#define R1_ERROR(X) (R1_PARAM_ERR(X) || R1_ADDR_ERR(X) || R1_ERASE_ERR(X) || \
                     R1_CMD_CRC_ERR(X) || R1_ILL_CMD_ERR(X))
 
/* see sd spec. 7.3.3.1 Data Response Token */
#define DATA_RESPONSE_IS_VALID(X)  (((X) & 0x11) == 0x01)
#define DATA_RESPONSE_ACCEPTED(X)  (((X) & 0x0E) == (1<<2))
#define DATA_RESPONSE_CRC_ERR(X)   (((X) & 0x0E) == 0x0A)
#define DATA_RESPONSE_WRITE_ERR(X) (((X) & 0x0E) == 0x0C)
 
/* see sd spec. 5.1 OCR register */
#define OCR_VOLTAGE_3_2_TO_3_3 (1L << 20)
#define OCR_VOLTAGE_3_3_TO_3_4 (1L << 21)
 
/* card capacity status (CCS=0: the card is SDSD; CCS=1: card is SDHC or SDXC) */
#define OCR_CCS (1L << 30)
 
/* This bit is set to low if the card has not finished power up routine */
#define OCR_POWER_UP_STATUS (1L << 31)
 
/* to ensure the voltage range check on init is done properly you need to
   define this according to your actual interface/wiring with the sd-card */
#define SYSTEM_VOLTAGE (OCR_VOLTAGE_3_2_TO_3_3 | OCR_VOLTAGE_3_2_TO_3_3)
 
/* see sd spec. 7.3.1.3 Detailed Command Description */
#define SD_CMD_PREFIX_MASK (1<<6)
 
#define SD_CMD_0 0   /* Resets the SD Memory Card */
#define SD_CMD_1 1   /* Sends host capacity support info and starts the cards init process */
#define SD_CMD_8 8   /* Sends SD Card interface condition incl. host supply voltage info */
#define SD_CMD_9 9   /* Asks the selected card to send its card-specific data (CSD) */
#define SD_CMD_10 10 /* Asks the selected card to send its card identification (CID) */
#define SD_CMD_12 12 /* Forces the card to stop transmission in Multiple Block Read Operation */
#define SD_CMD_13 13 /* Sent as ACMD13 asks the card to send it's SD status */
 
#define SD_CMD_16 16 /* In case of SDSC Card, block length is set by this command */
#define SD_CMD_17 17 /* Reads a block of the size selected by the SET_BLOCKLEN command */
#define SD_CMD_18 18 /* Continuously transfers data blocks from card to host
                        until interrupted by a STOP_TRANSMISSION command */
#define SD_CMD_24 24 /* Writes a block of the size selected by the SET_BLOCKLEN command */
#define SD_CMD_25 25 /* Continuously writes blocks of data until 'Stop Tran'token is sent */
#define SD_CMD_41 41 /* Reserved (used for ACMD41) */
#define SD_CMD_55 55 /* Defines to the card that the next command is an application specific
                        command rather than a standard command */
#define SD_CMD_58 58 /* Reads the OCR register of a card */
#define SD_CMD_59 59 /* Turns the CRC option on or off. Argument: 1:on; 0:off */
 
#define SD_CMD_8_VHS_2_7_V_TO_3_6_V 0x01
#define SD_CMD_8_CHECK_PATTERN      0xB5
#define SD_CMD_NO_ARG     0x00000000
#define SD_ACMD_41_ARG_HC 0x40000000
#define SD_CMD_59_ARG_EN  0x00000001
#define SD_CMD_59_ARG_DIS 0x00000000
 
/* see sd spec. 7.3.3 Control Tokens */
#define SD_DATA_TOKEN_CMD_17_18_24 0xFE
#define SD_DATA_TOKEN_CMD_25       0xFC
#define SD_DATA_TOKEN_CMD_25_STOP  0xFD
 
#define SD_SIZE_OF_CID_AND_CSD_REG 16
#define SD_SIZE_OF_SD_STATUS 64
#define SD_BLOCKS_FOR_REG_READ 1
#define SD_GET_CSD_STRUCTURE(CSD_RAW_DATA) ((CSD_RAW_DATA)[0] >> 6)
#define SD_CSD_V1 0
#define SD_CSD_V2 1
#define SD_CSD_VUNSUPPORTED -1
 
#ifndef INIT_CMD_RETRY_US
#define INIT_CMD_RETRY_US           (250 * US_PER_MS) 
#endif
#ifndef INIT_CMD0_RETRY_US
#define INIT_CMD0_RETRY_US          (100UL)           
#endif
#ifndef R1_POLLING_RETRY_US
#define R1_POLLING_RETRY_US         (100 * US_PER_MS) 
#endif
#ifndef SD_DATA_TOKEN_RETRY_US
#define SD_DATA_TOKEN_RETRY_US      (100 * US_PER_MS) 
#endif
#ifndef SD_WAIT_FOR_NOT_BUSY_US
#define SD_WAIT_FOR_NOT_BUSY_US     (250 * US_PER_MS) 
#endif
#ifndef SD_BLOCK_READ_CMD_RETRY_US
#define SD_BLOCK_READ_CMD_RETRY_US  (100UL)           
#endif
#ifndef SD_BLOCK_WRITE_CMD_RETRY_US
#define SD_BLOCK_WRITE_CMD_RETRY_US (100UL)           
#endif
#define SD_CSD_V2_C_SIZE_BLOCK_MULT 1024
 
#ifndef SD_CARD_SPI_MODE
#define SD_CARD_SPI_MODE SPI_MODE_0
#endif
 
#ifndef SD_CARD_SPI_SPEED_PREINIT
#define SD_CARD_SPI_SPEED_PREINIT SPI_CLK_400KHZ
#endif
 
#ifndef SD_CARD_SPI_SPEED_POSTINIT
#define SD_CARD_SPI_SPEED_POSTINIT SPI_CLK_10MHZ
#endif
 
#define SD_CARD_DUMMY_BYTE  (0xFF)
 
#define SDCARD_SPI_IEC_KIBI (1024L)
 
#define SDCARD_SPI_SI_KILO  (1000L)
 
typedef enum {
    SD_INIT_START,
    SD_INIT_SPI_POWER_SEQ,
    SD_INIT_SEND_CMD0,
    SD_INIT_SEND_CMD8,
    SD_INIT_CARD_UNKNOWN,
    SD_INIT_SEND_ACMD41_HCS,
    SD_INIT_SEND_ACMD41,
    SD_INIT_SEND_CMD1,
    SD_INIT_SEND_CMD58,
    SD_INIT_SEND_CMD16,
    SD_INIT_ENABLE_CRC,
    SD_INIT_READ_CID,
    SD_INIT_READ_CSD,
    SD_INIT_SET_MAX_SPI_SPEED,
    SD_INIT_FINISH
} sd_init_fsm_state_t;
uint8_t sdcard_spi_send_cmd(sdcard_spi_t *card, uint8_t sd_cmd_idx, uint32_t argument, uint32_t retry_us);
 
uint8_t sdcard_spi_send_acmd(sdcard_spi_t *card, uint8_t sd_cmd_idx, uint32_t argument, uint32_t retry_us);
 
uint32_t sdcard_spi_get_sector_count(sdcard_spi_t *card);
 
uint32_t sdcard_spi_get_au_size(sdcard_spi_t *card);
 
sd_rw_response_t sdcard_spi_read_sds(sdcard_spi_t *card, sd_status_t *sd_status);
 
#ifdef __cplusplus
}
#endif