CC26x2/CC13x2 Device setup functions. More...

Detailed Description

CC26x2/CC13x2 Device setup functions.

Definition in file cc26x2_cc13x2_setup.h.

#include <cc26xx_cc13xx.h>

Include dependency graph for cc26x2_cc13x2_setup.h:

This graph shows which files directly or indirectly include this file:

Go to the source code of this file.

Functions
void	setup_trim_device (void)
	Performs the necessary trim of the device which is not done in ROM boot code. More...

#define	ROM_API_SETUP ((uint32_t *) (ROM_API_TABLE[28]))
	Setup API address.

#define	rom_setup_after_cold_reset_wakeup_from_shutdown_cfg1 ((void (*)(uint32_t mode_conf))ROM_API_SETUP[0])
	Setup API ROM functions.

#define	rom_setup_after_cold_reset_wakeup_from_shutdown_cfg2 ((void (*)(uint32_t rev, uint32_t mode_conf))ROM_API_SETUP[1])

#define	rom_setup_after_cold_reset_wakeup_from_shutdown_cfg3 ((void (*)(uint32_t mode_conf))ROM_API_SETUP[2])

#define	rom_setup_get_trim_for_adc_sh_mode_en ((uint32_t (*)(uint32_t rev))ROM_API_SETUP[3])

#define	rom_setup_get_trim_for_adc_sh_vbuf_en ((uint32_t (*)(uint32_t rev))ROM_API_SETUP[4])

#define	rom_setup_get_trim_for_ampcomp_ctrl ((uint32_t (*)(uint32_t rev))ROM_API_SETUP[5])

#define	rom_setup_get_trim_for_ampcomp_th1 ((uint32_t (*)(void))ROM_API_SETUP[6])

#define	rom_setup_get_trim_for_ampcomp_th2 ((uint32_t (*)(void))ROM_API_SETUP[7])

#define	rom_setup_get_trim_for_anabypass_value1 ((uint32_t (*)(uint32_t mode_conf))ROM_API_SETUP[8])

#define	rom_setup_get_trim_for_dblr_loop_filter_reset_voltage ((uint32_t (*)(uint32_t rev))ROM_API_SETUP[9])

#define	rom_setup_get_trim_for_radc_ext_cfg ((uint32_t (*)(uint32_t rev))ROM_API_SETUP[10])

#define	rom_setup_get_trim_for_rc_osc_lf_ibias_trim ((uint32_t (*)(uint32_t rev))ROM_API_SETUP[11])

#define	rom_setup_get_trim_for_rc_osc_lf_rtune_ctune_trim ((uint32_t (*)(void))ROM_API_SETUP[12])

#define	rom_setup_get_trim_for_xosc_hf_ctl ((uint32_t (*)(uint32_t rev))ROM_API_SETUP[13])

#define	rom_setup_get_trim_for_xosc_hf_fast_start ((uint32_t (*)(void))ROM_API_SETUP[14])

#define	rom_setup_get_trim_for_xosc_hf_ibiastherm ((uint32_t (*)(void))ROM_API_SETUP[15])

#define	rom_setup_get_trim_for_xosc_lf_regulator_and_cmirrwr_ratio ((uint32_t (*)(uint32_t rev))ROM_API_SETUP[16])

#define	rom_setup_set_aon_rtc_sub_sec_inc ((void (*)(uint32_t subsecinc))ROM_API_SETUP[17])

#define	rom_setup_set_cache_mode_according_to_ccfg_setting ((void (*)(void))ROM_API_SETUP[18])

#define	rom_setup_step_vddr_trim_to ((void (*)(uint32_t tocode))ROM_API_SETUP[19])

Function Documentation

◆ setup_trim_device()

void setup_trim_device ( void )

Performs the necessary trim of the device which is not done in ROM boot code.

The following is handled by this function:

Checks if the driverlib variant used by the application is supported by the device. Execution is halted in case of unsupported driverlib variant.
Configures VIMS cache mode based on setting in CCFG.
Configures functionalities like DCDC and XOSC dependent on startup modes like cold reset, wakeup from shutdown and wakeup from from powerdown.
Configures VIMS power domain control.
Configures optimal wait time for flash FSM in cases where flash pump wakes up from sleep.

Note: It does no damage to execute this function again. It only consumes time.

Detailed Description

Functions

Function Documentation

◆ setup_trim_device()