lm75_params.h File Reference
Default configuration parameters for the lm75 sensors. More...
Detailed Description
Default configuration parameters for the lm75 sensors.
Definition in file lm75_params.h.
Include dependency graph for lm75_params.h:Go to the source code of this file.
| #define | LM75_PARAM_I2C I2C_DEV(0) |
| I2C BUS used. | |
| #define | CONFIG_LM75_I2C_ADDR (0x48) |
| 7-bit I2C slave address: 1-0-0-1-A2-A1-A0, where the last three bits A2, A1, A0 are defined by the voltage level on the ADDR pin More... | |
| #define | CONFIG_OPERATION_MODE NORMAL_MODE |
| Normal Mode is the default. | |
| #define | CONFIG_THERMOSTAT_MODE COMPARATOR_MODE |
| Comparator Mode is the default. | |
| #define | CONFIG_OS_POLARITY OS_ACTIVE_LOW |
| OS pin active on low is the default. | |
| #define | CONFIG_FAULT_QUEUE FAULT_1 |
| One Fault is the default. | |
| #define | LM75_PARAM_INT GPIO_UNDEF |
| Pin used for Interrupts defined by the board. | |
| #define | LM75A_CONV_RATE (100) |
| temperature register updated every 100ms | |
| #define | LM75A_OS_RES (5) |
| resolution in 0.5ºC | |
| #define | LM75A_OS_MULT (10) |
| Must multiply by 10 to get temp in ºC. | |
| #define | LM75A_OS_SHIFT (7) |
| Only the 9 most significant bits are needed. | |
| #define | LM75A_TEMP_RES (125) |
| resolution in 0.125ºC | |
| #define | LM75A_TEMP_MULT (1000) |
| Must multiply by 1000 to get temp in ºC. | |
| #define | LM75A_TEMP_SHIFT (5) |
| Only the 11 most significant bits are needed. | |
| #define | TMP1075_OS_RES (625) |
| resolution in 0.0625ºC | |
| #define | TMP1075_OS_MULT (10000) |
| Must multiply by 10000 to get temp in ºC. | |
| #define | TMP1075_OS_SHIFT (4) |
| Only the 12 most significant bits are needed. | |
| #define | TMP1075_TEMP_RES (625) |
| resolution in 0.0625ºC | |
| #define | TMP1075_TEMP_MULT (10000) |
| Must multiply by 10000 to get temp in ºC. | |
| #define | TMP1075_TEMP_SHIFT (4) |
| Only the 12 most significant bits are needed. | |
| #define | CONFIG_TMP1075_CONV_RATE_REG TMP1075_CONV_RATE_REG_27H |
| Default conv rate is 27.5ms. | |
| #define | TMP1075_CONV_RATE (28) |
| Default conversion rate is 27.5 ms. | |
| static const lm75_params_t | lm75_params [] |
| LM75 power-up configuration. More... | |
Macro Definition Documentation
◆ CONFIG_LM75_I2C_ADDR
| #define CONFIG_LM75_I2C_ADDR (0x48) |
7-bit I2C slave address: 1-0-0-1-A2-A1-A0, where the last three bits A2, A1, A0 are defined by the voltage level on the ADDR pin
Default I2C address
Definition at line 38 of file lm75_params.h.
Variable Documentation
◆ lm75_params
|
static |
Initial value:
=
{
LM75_PARAMS
}
LM75 power-up configuration.
Definition at line 170 of file lm75_params.h.
