45 #ifdef MODULE_LIS2DH12_SPI 
   55 #if defined(MODULE_LIS2DH12) || defined(DOXYGEN) 
   59 #define LIS2DH12_ADDR_DEFAULT       (0x19) 
  100 #define LIS2DH12_CLICK_X_SINGLE (1 << 0)     
  101 #define LIS2DH12_CLICK_X_DOUBLE (1 << 1)     
  102 #define LIS2DH12_CLICK_Y_SINGLE (1 << 2)     
  103 #define LIS2DH12_CLICK_Y_DOUBLE (1 << 3)     
  104 #define LIS2DH12_CLICK_Z_SINGLE (1 << 4)     
  105 #define LIS2DH12_CLICK_Z_DOUBLE (1 << 5)     
  111 #if MODULE_LIS2DH12_SPI || DOXYGEN 
  118 #if MODULE_LIS2DH12_INT || DOXYGEN 
  253 #if MODULE_LIS2DH12_INT || DOXYGEN 
  267                                   uint32_t mg, uint32_t us,
 
  268                                   uint8_t axis, uint8_t 
event, uint8_t pin);
 
  287                               uint32_t us_limit, uint32_t us_latency, uint32_t us_window,
 
  288                               uint8_t click, uint8_t pin);
 
Low-level GPIO peripheral driver interface definitions.
 
lis2dh12_scale_t
Available scale values.
 
int lis2dh12_set_datarate(const lis2dh12_t *dev, lis2dh12_rate_t rate)
Change device sampling rate.
 
int lis2dh12_set_resolution(const lis2dh12_t *dev, lis2dh12_resolution_t resolution)
Change device resolution.
 
lis2dh12_fifo_mode_t
LIS2DH12 FIFO modes.
 
uint16_t lis2dh12_get_datarate(const lis2dh12_t *dev)
Get device sampling rate in Hz.
 
int32_t lis2dh12_wait_event(const lis2dh12_t *dev, uint8_t pin, bool stale_events)
Wait for an interrupt event This function will block until an interrupt is received.
 
void lis2dh12_cfg_threshold_event(const lis2dh12_t *dev, uint32_t mg, uint32_t us, uint8_t axis, uint8_t event, uint8_t pin)
Configure a threshold event An Interrupt will be generated if acceleration exceeds the set threshold ...
 
int lis2dh12_restart_fifo(const lis2dh12_t *dev)
Restart the FIFO mode this sets the FIFO mode in BYPASS mode and then back to previous mode Note: The...
 
lis2dh12_resolution_t lis2dh12_get_resolution(const lis2dh12_t *dev)
Get device resolution.
 
lis2dh12_hp_freq_t
LIS2DH12 high pass cutoff frequency.
 
lis2dh12_scale_t lis2dh12_get_scale(lis2dh12_t *dev)
Get device measuring range.
 
int lis2dh12_set_scale(lis2dh12_t *dev, lis2dh12_scale_t scale)
Change device measuring range.
 
void lis2dh12_cfg_click_event(const lis2dh12_t *dev, uint32_t mg, uint32_t us_limit, uint32_t us_latency, uint32_t us_window, uint8_t click, uint8_t pin)
Configure a click event A click event is generated when the acceleration exceeds the set threshold fo...
 
int lis2dh12_clear_data(const lis2dh12_t *dev)
Clear the LIS2DH12 memory, clears all sampled data.
 
int lis2dh12_set_reference(const lis2dh12_t *dev, uint8_t reference)
Set the reference value to control the high-pass reference.
 
int lis2dh12_read(const lis2dh12_t *dev, lis2dh12_fifo_data_t *data)
Read acceleration data from the given device.
 
const saul_driver_t lis2dh12_saul_driver
Export the SAUL interface for this driver.
 
int lis2dh12_read_temperature(const lis2dh12_t *dev, int16_t *temp)
Read temperature data from the given device.
 
lis2dh12_rate_t
Available sampling rates.
 
int lis2dh12_set_fifo(const lis2dh12_t *dev, const lis2dh12_fifo_t *config)
Set the FIFO configuration.
 
lis2dh12_resolution_t
Available resolutions.
 
int lis2dh12_poweron(const lis2dh12_t *dev)
Power on the given device and resets resolution and sampling rate to default values in the device des...
 
uint8_t lis2dh12_read_fifo_data(const lis2dh12_t *dev, lis2dh12_fifo_data_t *fifo_data, uint8_t number)
This function will read a given number of data from FIFO reads amount of data that is available in FI...
 
int lis2dh12_set_highpass(const lis2dh12_t *dev, const lis2dh12_highpass_t *config)
Configures the high pass filter.
 
int lis2dh12_poweroff(const lis2dh12_t *dev)
Power off the given device.
 
lis2dh12_hp_mode_t
LIS2DH12 high pass modes.
 
int lis2dh12_init(lis2dh12_t *dev, const lis2dh12_params_t *params)
Initialize the given LIS2DH12 sensor device.
 
void lis2dh12_cfg_disable_event(const lis2dh12_t *dev, uint8_t event, uint8_t pin)
Disable interrupt generation for an event This disables an interrupt on pin if a previously configure...
 
@ LIS2DH12_SCALE_16G
+- 16g
 
@ LIS2DH12_NODEV
unable to talk to device
 
@ LIS2DH12_NODATA
no data available
 
@ LIS2DH12_NOBUS
bus interface error
 
@ LIS2DH12_OK
everything was fine
 
@ LIS2DH12_NOINT
wrong interrupt line (has to be LIS2DH12_INT1 or LIS2DH12_INT2)
 
@ LIS2DH12_FIFO_MODE_BYPASS
default mode, FIFO is bypassed
 
@ LIS2DH12_FIFO_MODE_STREAM
Stream mode, oldest values get overwritten.
 
@ LIS2DH12_FIFO_MODE_FIFOMODE
normal FIFO mode, stops if FIFO is full
 
@ LIS2DH12_FIFO_MODE_STREAMtoFIFO
Stream mode and on interrupt jumps to FIFO mode.
 
@ LIS2DH12_HP_FREQ_DIV100
cutoff freq is ODR divided by 100
 
@ LIS2DH12_HP_FREQ_DIV200
cutoff freq is ODR divided by 200
 
@ LIS2DH12_HP_FREQ_DIV50
cutoff freq is ODR divided by 50
 
@ LIS2DH12_HP_FREQ_DIV400
cutoff freq is ODR divided by 400
 
@ LIS2DH12_RATE_400HZ
sample with 400Hz @ all resolutions
 
@ LIS2DH12_RATE_200HZ
sample with 200Hz @ all resolutions
 
@ LIS2DH12_RATE_1620HZ
sample with 1620HZ @ 8-bit
 
@ LIS2DH12_RATE_VERYHIGH
sample with 1344Hz @ High resolution or \ 5376Hz @ 8-bit
 
@ LIS2DH12_RATE_50HZ
sample with 50Hz @ all resolutions
 
@ LIS2DH12_RATE_25HZ
sample with 25Hz @ all resolutions
 
@ LIS2DH12_RATE_1HZ
sample with 1Hz @ all resolutions
 
@ LIS2DH12_RATE_10HZ
sample with 10Hz @ all resolutions
 
@ LIS2DH12_RATE_100HZ
sample with 100Hz @ all resolutions
 
@ LIS2DH12_POWER_LOW
8-bit mode
 
@ LIS2DH12_POWER_DOWN
power down the device
 
@ LIS2DH12_POWER_NORMAL
10-bit mode
 
@ LIS2DH12_POWER_HIGH
12-bit mode
 
@ LIS2DH12_INT1
first interrupt line
 
@ LIS2DH12_INT2
second interrupt line
 
@ LIS2DH12_HP_MODE_NORMAL
normal mode, reset by reading REG_REFERENCE
 
@ LIS2DH12_HP_MODE_REFERENCE
uses the reference signal for filtering
 
@ LIS2DH12_HP_MODE_AUTORESET
automatically resets on interrupt generation
 
uint_fast8_t i2c_t
Default i2c_t type definition.
 
Low-level I2C peripheral driver interface definition.
 
LIS2DH12 register definitions.
 
Low-level SPI peripheral driver interface definition.
 
LIS2DH12 click config values.
 
bool enable_DOUBLE
otherwise single click for given axis are enabled
 
uint8_t TIME_latency
set number of ODR cycles for latency after a click
 
bool noINT_latency
if "0" interrupt stays high for TIME_latency setting \ if "1" interrupt stays high until CLICK_SRC is...
 
uint8_t TIME_window
set number of ODR cycles for window between clicks
 
bool enable_Y_CLICK
enable double pr single click for Y axes
 
bool enable_X_CLICK
enable double pr single click for X axes
 
uint8_t CLICK_thold
set click threshold
 
uint8_t TIME_limit
set number of ODR cycles for time limit over threshold value
 
bool enable_Z_CLICK
enable double pr single click for Z axes
 
LIS2DH12 FIFO config values.
 
bool FIFO_set_INT2
sets the FIFO interrupt to INT2, otherwise INT1
 
uint8_t FIFO_watermark
set the FIFO watermark level
 
lis2dh12_fifo_mode_t FIFO_mode
set FIFO mode
 
LIS2DH12 high pass config values.
 
bool INT2_enable
enables filter for AOI on interrupt 2
 
bool CLICK_enable
enables filter for click data
 
bool INT1_enable
enables filter for AOI on interrupt 1
 
lis2dh12_hp_mode_t Highpass_mode
set the High pass mode
 
lis2dh12_hp_freq_t Highpass_freq
set the High pass cutoff frequency \ related to device rate
 
bool DATA_OUT_enable
enables filter for data output
 
Parameter for interrupt configuration.
 
uint8_t int_config
values for configuration
 
uint8_t int_threshold
the threshold for triggering interrupt, threshold in range 0-127
 
uint8_t int_type
values for type of interrupts
 
uint8_t int_duration
time between two interrupts ODR section in CTRL_REG1, duration in range 0-127
 
LIS2DH12 configuration parameters.
 
lis2dh12_resolution_t resolution
resolution used
 
gpio_t cs
connected chip select pin
 
spi_t spi
SPI bus the device is connected to.
 
lis2dh12_rate_t rate
sampling rate used
 
gpio_t int1_pin
first interrupt pin
 
lis2dh12_scale_t scale
sampling sensitivity used
 
gpio_t int2_pin
second interrupt pin
 
LIS2DH12 device descriptor.
 
const lis2dh12_params_t * p
device configuration
 
Definition of the RIOT actuator/sensor interface.
 
Functionality for reading [S]ensor [A]ctuator [U]ber [L]ayer sensors as SenML.
 
LIS2DH12 FIFO data struct.
 
int16_t y
Y data in mili-g.
 
int16_t z
Z data in mili-g.
 
int16_t x
X data in mili-g.