periph_conf.h File Reference

Peripheral MCU configuration for the Microchip SAM R34 Xplained Pro board. More...

Detailed Description

Peripheral MCU configuration for the Microchip SAM R34 Xplained Pro board.

Author

Dylan Laduranty dylan.nosp@m..lad.nosp@m.urant.nosp@m.y@me.nosp@m.sotic.nosp@m..com

Definition in file periph_conf.h.

#include "periph_cpu.h"
#include "macros/units.h"

Include dependency graph for periph_conf.h:

Go to the source code of this file.

#define	CLOCK_CORECLOCK   MHZ(48)
	GCLK reference speed.
#define	USE_VREG_BUCK   (1)
	Enable the internal DC/DC converter The board is equipped with the necessary inductor.

Timer peripheral configuration
#define	TIMER_0_CHANNELS   2
#define	TIMER_0_ISR   isr_tc0
#define	TIMER_1_CHANNELS   2
#define	TIMER_1_ISR   isr_tc2
#define	TIMER_NUMOF   ARRAY_SIZE(timer_config)
static const tc32_conf_t	timer_config []

UART configuration
#define	UART_0_ISR   isr_sercom0
#define	UART_1_ISR   isr_sercom3
#define	UART_NUMOF   ARRAY_SIZE(uart_config)
static const uart_conf_t	uart_config []

SPI configuration
#define	SPI_NUMOF   ARRAY_SIZE(spi_config)
static const spi_conf_t	spi_config []

I2C configuration
#define	I2C_NUMOF   ARRAY_SIZE(i2c_config)
static const i2c_conf_t	i2c_config []

RTC configuration
#define	EXTERNAL_OSC32_SOURCE   1
#define	INTERNAL_OSC32_SOURCE   0
#define	ULTRA_LOW_POWER_INTERNAL_OSC_SOURCE   0

RTT configuration
#define	RTT_FREQUENCY   (32768U)

ADC Configuration
#define	ADC_PRESCALER   ADC_CTRLB_PRESCALER_DIV256
#define	ADC_NEG_INPUT   ADC_INPUTCTRL_MUXNEG(0x18u)
#define	ADC_REF_DEFAULT   ADC_REFCTRL_REFSEL_INTVCC2
#define	ADC_NUMOF   ARRAY_SIZE(adc_channels)
static const adc_conf_chan_t	adc_channels []

USB peripheral configuration
static const sam0_common_usb_config_t	sam_usbdev_config []

Variable Documentation

adc_channels

const adc_conf_chan_t adc_channels[]

static

Initial value:

= {
    
    { .inputctrl = ADC_INPUTCTRL_MUXPOS_PA06 },
    { .inputctrl = ADC_INPUTCTRL_MUXPOS_PA07 }
}

Definition at line 205 of file periph_conf.h.

i2c_config

const i2c_conf_t i2c_config[]

static

Initial value:

= {
    {
        .dev      = &(SERCOM1->I2CM),
        .speed    = I2C_SPEED_NORMAL,
        .scl_pin  = GPIO_PIN(PA, 17),
        .sda_pin  = GPIO_PIN(PA, 16),
        .mux      = GPIO_MUX_C,
        .gclk_src = SAM0_GCLK_MAIN,
        .flags    = I2C_FLAG_NONE
     }
}

Definition at line 162 of file periph_conf.h.

sam_usbdev_config

const sam0_common_usb_config_t sam_usbdev_config[]

static

Initial value:

= {
    {
        .dm       = GPIO_PIN(PA, 24),
        .dp       = GPIO_PIN(PA, 25),
        .d_mux    = GPIO_MUX_G,
        .device   = &USB->DEVICE,
        .gclk_src = SAM0_GCLK_48MHZ,
    }
}

Definition at line 218 of file periph_conf.h.

timer_config

const tc32_conf_t timer_config[]

static

Initial value:

= {
    {   
        .dev            = TC0,
        .irq            = TC0_IRQn,
        .mclk           = &MCLK->APBCMASK.reg,
        .mclk_mask      = MCLK_APBCMASK_TC0_Msk | MCLK_APBCMASK_TC1_Msk,
        .gclk_id        = TC0_GCLK_ID,
        .gclk_src       = SAM0_GCLK_TIMER,
        .flags          = TC_CTRLA_MODE_COUNT32,
    },
    {
        .dev            = TC2,
        .irq            = TC2_IRQn,
        .mclk           = &MCLK->APBCMASK.reg,
        .mclk_mask      = MCLK_APBCMASK_TC2_Msk | MCLK_APBCMASK_TC3_Msk,
        .gclk_id        = TC2_GCLK_ID,
        .gclk_src       = SAM0_GCLK_TIMER,
        .flags          = TC_CTRLA_MODE_COUNT32,
    }
}

Definition at line 45 of file periph_conf.h.

uart_config

const uart_conf_t uart_config[]

static

Initial value:

= {
    {    
        .dev      = &SERCOM0->USART,
        .rx_pin   = GPIO_PIN(PA, 5),
        .tx_pin   = GPIO_PIN(PA, 4),
 
 
 
 
        .mux      = GPIO_MUX_D,
        .rx_pad   = UART_PAD_RX_1,
        .tx_pad   = UART_PAD_TX_0,
        .flags    = UART_FLAG_NONE,
        .gclk_src = SAM0_GCLK_MAIN,
    },
    {    
        .dev      = &SERCOM3->USART,
        .rx_pin   = GPIO_PIN(PA, 17),
        .tx_pin   = GPIO_PIN(PA, 16),
 
 
 
 
        .mux      = GPIO_MUX_D,
        .rx_pad   = UART_PAD_RX_1,
        .tx_pad   = UART_PAD_TX_0,
        .flags    = UART_FLAG_NONE,
        .gclk_src = SAM0_GCLK_MAIN,
    }
}

Definition at line 78 of file periph_conf.h.